Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - lucasantini

Pages: [1]
1
Brammo Enertia Plus / Re: system fault c3
« on: November 21, 2018, 03:32:53 AM »
Hello at everyone.

I decided to sell my enertia plus , with the system fault c3 problem. The bike have only  5300 km

If someone is interested write me on email at santini1@hotmail.it or at whatsapp on +39 388 8571545

King regards, Luca

2
Brammo Enertia Plus / Re: system fault c3
« on: December 04, 2017, 04:18:41 AM »
Hello at everyone.

someone Know where I can find all the electric scheme of enertia brammo plus ?

BMS, ECU, etc ??

Really Thanks.


3
Brammo Enertia Plus / Re: system fault c3
« on: November 06, 2017, 01:54:44 PM »
hi I think I have just try, I think that there is something bad in my byke.

Where I can fond some part ? the bms etc ?

4
Brammo Enertia Plus / Re: system fault c3
« on: October 10, 2017, 11:50:32 AM »
hello karel,

where I can found new bms ? or new component ? cable, mainboard etc?


5
Brammo Enertia Plus / Re: system fault c3
« on: August 29, 2017, 06:55:50 PM »
Today I have work at brammo.
I have balanced manually all the cells,clean the contact of the bms boards,and I was thinking that was everything ok.
But bad news,my new error is system error b6.
Someone can give to me some contact to help with my problem.
The enertia don' t go from this april..I thinks after a run under a water.
I suppose that is a cable or board problem.The fuse unfortunately are all ok.
Where I can find assiatance or parts?
Thanks

6
Brammo Enertia Plus / Re: system fault c3
« on: August 09, 2017, 07:10:38 PM »
Really thanks kafr,
I'm balancing the battery with a small charger.
Today there is a good news and one bad news.
Finally the bms board read in the right mode the cell voltage,and I'm really happy about this.
The bad new is that the enertia turn on when i connect the main connector,with the key on off position.....
Booh...
Now i balance,when (one day) the enertia is running wirhout system error  i try to solve this new problem.
Really thanks at all for your support and sorry for my bad english.
Luca

7
Brammo Enertia Plus / Re: system fault c3
« on: August 08, 2017, 10:24:57 PM »
Hello,
The ann150 is ok,i have just cheked it.Is the main fuse,if the main fuse don'work the bike is died.
My enertia is not died I have a system error.
The error is present with the charger installed and not installed,so i suppose that the charger is ok.
Today I have understand an important things.
I have do some test and Finally I know how the enertia read the cell,and I'm trying  to balance with external charger, reading the lower on display,and charging it.
I think(and hope) that my error is about cell unbalanced with too Voltage of difference,and the charger can't balance it.
I'm trying this road,really thanks at all for the support.
If someone have idea,I'm here



8
Brammo Enertia Plus / Re: system fault c3
« on: August 04, 2017, 07:21:08 AM »
hello at everyone.
Really thanks for your answer.

Kafr : you are right.The bettarieres are not balanced, but the bike don't charge it.

I have try to maunually balance, with a small battery charger for rc car.I have charge all the cell at 4.10 voltage.
But now, when I have assemblie the bike, in the display i see different value.... I don't know why.

And now, another problem... when i connect the battery at the bike, the display go on whit the key on off position.Maybe this things can be the same problem.

I have check all the fuses, are all ok.
I have do a video, of my situation.

Please someone help me!

sorry for my bad english



Really thanks at all.

9
Brammo Enertia Plus / Re: system fault c3
« on: May 27, 2017, 11:57:59 AM »
Hi Ausiander.
Rewlly thanks for your answer.
the problem is that with this error,the charge not start.
Today i have open the two battery pack,and i have check all the Voltage.The cells are not balanced.
The highest value is 4.10v the Lowest is 3.68.
It is rrally strange.My last charge was 100%,i regharr every time to 100%.
So i would try to charge manually all the cell.
Today i have buy a computerized charger for liion cells,tonight i begin to recharge all the cells at 4.15v.
I think that this error is about the too high difference of Voltage.Maybe i can resolve the problem.My enertia is new...only 5000km...sigh
Sorry for my bad english...

10
Brammo Enertia Plus / Re: system fault c3
« on: May 17, 2017, 04:46:08 PM »
I have work on enertia today.
I have dismount a lot of pieces.

I have see that the led on the battery pack is green, but one times becomes red.
I have check the voltavg of the first 14 cell, and is 3,84 volts for all.
The second battery pack is under the motorbike, i can not open now.
What is the meaning of the red light??


11
Brammo Enertia Plus / Re: system fault c3
« on: May 16, 2017, 05:14:00 PM »
I had just try....nothing.
I have see on the display that the cell are not balanced, 4.000 the first value and 3.733 the second.Maybe I have to check some battery connector.Anyone have idea about it?

12
Brammo Enertia Plus / system fault c3
« on: May 16, 2017, 02:30:31 AM »
Hello,
My brammo enertia Plus, gives me system fault c3 error in the display.
The moto dont'go, and don't recharge the battery.
Fortunatley the bike have the battery at 71% of charge
I know that this error is not present on the brammo enertia plus owners manual,in my manual there isn't but I have it on the display


http://www.simonavisualmerchandiser.altervista.org/foto1.jpeg
http://www.simonavisualmerchandiser.altervista.org/foto2.jpeg

I can have problem with the software?
Info: i have 1,44 firmware.

Help!! The summer is at the door!!

13
Welcome Forum / Hello, From Italy, Pisa
« on: May 16, 2017, 02:12:34 AM »
Hi, I'm Luca Santini, I'm Italian, and i live Near Pisa.
I love all the electric mobilitiy and I have one brammo enertia Plus , red color.
Thanks at all


14
Brammo Enertia Plus / Re: Needs help in Italy
« on: May 16, 2017, 02:08:59 AM »
Really thanks  Richard

Pages: [1]