1
Victory Empulse / Re: Clutch plates.
« on: November 12, 2022, 11:12:22 AM »
I'm back on the road and the clutch feels so much better when changing gear.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Victory Empulse / Re: Clutch plates.
« on: October 30, 2022, 12:41:51 PM »
Hi All
I decided to stick with the 2.3mm as it worked out just fine, the options are there for someone else to try.
I'm waiting on just one fibre plate from a seller who has new old stock for sale, then I'm back on the road....again.
Sean
I decided to stick with the 2.3mm as it worked out just fine, the options are there for someone else to try.
I'm waiting on just one fibre plate from a seller who has new old stock for sale, then I'm back on the road....again.
Sean
3
Victory Empulse / Re: Clutch plates.
« on: October 27, 2022, 08:39:33 AM »
With the help from Mike from Barnett clutches in the US, I've found the correct plates that do fit my TT, they also fit the 05-06 Suzuki GSXR1000, part numbers are 21451-41G00 for the steel plates and 21441-36F00 for the fibre/friction plates, I've only so far purchased one of each plate to confirm fitment, the fibre plates are the same thickness but the steel plates are thicker (std 1.5mm-GSXR1000 2.3mm) so instead of the 8 friction 7 steels, I'll be fitting 7 friction and 6 steel, this will add 0.8 to the complete pack compared to standard pack, I will be keeping an eye on the clutch springs when I test the action of the clutch to check the springs for possible coil bound.
SeanTT
SeanTT
4
Victory Empulse / Re: Clutch plates.
« on: October 18, 2022, 10:13:29 AM »
Barnets have a number of 28 tooth plates but need the TT plate to match the correct tooth shape, also I found a perfect fit for the friction plate, its for a Suzuki part number 21441-36f00, also look better quality too.
6
Victory Empulse / Re: Clutch plates.
« on: October 15, 2022, 01:45:04 PM »
They are just a set that were the correct for fork tube diameter, they sit about 10mm lower for my liking, the handle bar tube makes contact with the top yoke pinch bolt surround.
8
Victory Empulse / Re: Clutch plates.
« on: October 15, 2022, 12:37:40 PM »
I had emailed wemoto uk and barnett clutches, wemoto say they have nothing that matches the measurements i gave, just waiting on barnett now, but today i rebuilt the TT clutch but leaving out the badly warped steel plate and having two fibre plates together at the outer end of the pack, i wasn't sure if the pressure plate would sit 1.5mm further back but it was fine and when the clutch lever was pulled the clutch was disengaged! with no drag, next issue would be if it would slip in 1st up a steep hill, well after a test ride it did not slip at all, so I'm back on the road, ill still be researching for the clutch plates, ill update here if i find anything.
ive added a 675 triumph fairing to my TT, if i can get the image size down ill upload it here also.
thanks for your help, guys.
ive added a 675 triumph fairing to my TT, if i can get the image size down ill upload it here also.
thanks for your help, guys.
9
Victory Empulse / Re: Clutch plates.
« on: October 15, 2022, 08:08:05 AM »
The steel plate is a no go, I'm still waiting for the friction plate.
10
Victory Empulse / Re: Clutch plates.
« on: October 11, 2022, 11:38:46 AM »
Ive narrowed it down to a RM125, i have ordered one plain plate and one friction plate with a part number, Ill update when they arrive and tested for fit.
Se
Se
12
Victory Empulse / Re: Clutch plates.
« on: October 10, 2022, 01:52:55 PM »
I cant get the image below the 500kb limit.
13
Victory Empulse / Re: Clutch plates.
« on: October 10, 2022, 12:42:55 PM »
Rm125 seem very similar but are 1.4mm thick
14
Victory Empulse / Re: Clutch plates.
« on: October 10, 2022, 12:40:43 PM »
Nothing on the friction plates.
15
Victory Empulse / Re: Clutch plates.
« on: October 10, 2022, 12:40:03 PM »
132mm outside diameter, 28 teeth, 1.5 thick.