Brammo Owners Forum
Brammo Enertia Discussion => Brammo Enertia => Topic started by: jazz999 on December 20, 2016, 01:37:54 PM
-
Do you think something like this would work for the Enertia charging? My city has been adding many more j1772 stations but no 110v so I cannot use them.
http://300mpg.org/2015/03/31/the-diy-j1772-charging-adapter/ (http://300mpg.org/2015/03/31/the-diy-j1772-charging-adapter/)
-
To update this. I was told by the manufacturer that this would work. Any opinions
https://www.amazon.com/gp/product/B00VIKM62Q/ref=s9_acsd_hps_bw_c_x_1_w (https://www.amazon.com/gp/product/B00VIKM62Q/ref=s9_acsd_hps_bw_c_x_1_w)
-
Two different things.
1. http://300mpg.org/2015/03/31/the-diy-j1772-charging-adapter/ (http://300mpg.org/2015/03/31/the-diy-j1772-charging-adapter/)
This is a J1772 inlet to allow you to connect an non-J1772 charging equipment to a J1772 supply, like most commercial car charging stations. Assuming that your charging equipment is compatible with 240V.
This should work fine to let you plug the Enertia charger into a J1772 EVSE. Note that this WILL NOT increase the speed that you charge at, and depending on the station may be quite expensive. Blink charges $0.04/minute for members, you're using approximately $0.0016 of electricity per minute. 2500% markup!
2. https://www.amazon.com/gp/product/B00VIKM62Q/ (https://www.amazon.com/gp/product/B00VIKM62Q/)
This is portable J1772 EVSE to allow you to connect a J1772 charger to a non-J1772 supply.
You're adding a lot of weight and cost for flexibility; in effect these two things together do the same thing as a $5 IEC C19 cable (connect 120V wall plug to vehicle for charging), but also give you more flexibility to plug into a J1772 supply or later to connect another type of J1772 EV to a 120V or 240V wall supply.
-
Thanks, appreciate the info. I think I read somewhere that the Enertia can handle 240v but not sure. Anyway, I just want to be able to charge it. I don't really want to add the additional weight but lack of 120v pluggins is making it difficult to charge away from home. My work is putting in 4 charging stations but they will only be J1772 only. Thanks again
-
:( They just added a new charging station right next to my office but level 2 only no 110v....sadly
-
Update: The Enertia Charge controller specs are:
100-240v
50-60Hz
720w
output 72v-720w
So the Zero to J1772 adapter should work: http://www.tucsonev.com/ (http://www.tucsonev.com/) for $100. I am going to buy it and try it out in the next couple of weeks.
-
Update: The Enertia Charge controller specs are:
100-240v
50-60Hz
720w
output 72v-720w
So the Zero to J1772 adapter should work: http://www.tucsonev.com/ (http://www.tucsonev.com/) for $100. I am going to buy it and try it out in the next couple of weeks.
Did this adapter ever work for you?
-
I actually never ended up going with it. I am pretty sure it would have worked though. I got an Empulse R and mostly been riding that the past year or so and not my Enertia so much. The Empulse R already has level 2 charging which met my needs. I'll probably sell my Enertia.
-
Where are you located?
-
Washington State