Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - brugja

Pages: [1]
1
Brammo Empulse / Re: Reading Log Files
« on: September 13, 2019, 12:57:21 PM »
i once recieved this mail conversation, and i managed to read my logs.

==============================
So you must install a couple things

First install this, which is the Brammo service software. I don't know much about it, and can't help as I don't have my Brammo any longer.
https://drive.google.com/open?id=1JXfwAXGOPEx8jSnmLsLxorQ5gn6HFkDB


Then you can run this program (copy both files to a directory on your hard drive), which reads the log file:
https://drive.google.com/file/d/1zWjaV79Oy2efwURpxnnr8o1OsQX-BChX/view?usp=sharing
https://drive.google.com/file/d/1-fTIftb0y3aVNQXlR0niWtblr0zE5FUK/view?usp=sharing

The Brammo software should be installed as it installs some Labview files that the log viewer is dependent on.

good luck.

2
Brammo Empulse / Re: Fuses
« on: November 13, 2018, 02:46:48 PM »
heel korte zoektocht kwam dit uit,

https://www.littelfuse.com/products/fuses/automotive-passenger-car/blade-fuses/fun.aspx

Proberen waard!? Hebben ook meerdere dealers in Nederland, misschien de moeite waard om een telefoontje aan te wagen!

3
Brammo Empulse / Re: Charger shows 0 Amps
« on: February 10, 2018, 08:04:55 AM »
hello Dietmar,

this might be the solution, where did you get the software?


4
Brammo Empulse / Re: battery safety interlock open
« on: January 24, 2018, 02:27:28 PM »
Quote from: BrammoQC on January 22, 2018, 08:35:53 PM
Incorrect, the interlock is an internal safety feature to the battery module. There is no Plug or Switch. The interlock can be reset via a PC with the proper software...and yes I know this will be difficult to find but I'm sure someone out there or a former Brammo/Victory dealer may have the capability. Bigger question, why did the interlock trip? Sorry to be somewhat vague, just trying to point you in the correct direction.

DH

thank you,

now i have to find someone with that software.....problems.....problems....problems.....  :-[ :-[ :-[ :-[ :-[

5
Brammo Empulse / battery safety interlock open
« on: January 20, 2018, 05:29:55 AM »
my log file gives this AIM message; Battery safety interlock open


What does it mean and how to get rid of it??

6
Brammo Empulse / Re: Red blinking led battery
« on: January 20, 2018, 05:04:40 AM »
No the bike isn't working. The whole story: Bike didn't want to charge, left the charger onit so the bike went empty. After searching and some tips i find a melted connector, i fixed this. Then i had charged the first battery (untherneath the sadle, tip from here) that didn't help to get the charging going. Then i hooked up a battery to the 12V output, wich did turn on the bike. But the charger didn't turn on. And there where errors C2, C3. I managed to get the logfile, i will send you the last part of it, mayby you can see something in this log.

By the way, i also charged the battery with the red blinking led, that didn't do anything.

thanks in advance.

7
Brammo Empulse / Red blinking led battery
« on: January 18, 2018, 02:06:27 PM »
has Anybody anny idea what the red blinking led means on 1 of my battery's? All the others are blinking green.
And more important does anybody know wha to do about it.

 :-[ :-[ :-[ :-[

8
Brammo Empulse / Software ??
« on: January 18, 2018, 04:54:06 AM »
Is there anybody who can help me to get software to read the log files?

9
Brammo Empulse / empty bike
« on: January 03, 2018, 09:40:29 AM »
my bike had a melted connector, wich i replaced. But my bike is completly empty, so the charger doesn't get a starting signal.

Anybody an idea? Charge it a little bit through te 12V connection with a rc lipo charger?


10
Brammo Empulse / Re: Charger shows 0 Amps
« on: January 03, 2018, 09:14:01 AM »
i had the same problem, no more charging. There was a melted connector untherneat the J1772 connector.

It is the outcoming cable from the charger. I have replaced it with some other connectors. Only problem that i now have is that my bike is completly out of power, so the charger won't start.

So if anybody has a solution for that.....


11
Brammo Empulse / Re: HELP System fault C2
« on: January 03, 2018, 08:57:37 AM »
aparently it was a melted connector wich i have replaced, but now it still doesn't want to start charging because my bike is completly empty so it doesn't give a signal to start charging.

Any suggestions?

12
Brammo Empulse / Re: HELP System fault C2
« on: December 23, 2017, 05:01:50 AM »
Quote from: frodus on December 21, 2017, 11:54:19 AM
C2 is a generic charger fault, if that helps.

Wich charger do they mean by that, the lead or the one inside the bike? Do you have some more information about this?

13
Brammo Empulse / HELP System fault C2
« on: December 21, 2017, 02:30:50 AM »
Hello,
My bike doesn't charge anymore, it gives a C2 error. I saw the topic with the 0 amps charge and i read the topic about the melted connectors. Is there anybody who can tell me witch connectors they are referring to? Are they talking about the charger connector on the "tank" or are they talking about the charger inside the motorcycle?

Any other options are welcome.

thanks in advance

Pages: [1]