Author Topic: Brammo Software  (Read 7100 times)

MiBa

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: Brammo Software
« Reply #15 on: April 04, 2019, 10:34:45 AM »
Win10 64-bit

An automatic "driver search" has not taken place. 

However, you may have to try the latest (?) SW from Victory. 
Battery Diagnostic 1.0.11.41

http://environ-systems.de/mediapool/132/1325968/data/64956043_02_Battery_Diagnostics-1.0.11.41.exe

On my Laptop "COM4" has been selected.

Regards

nunux59

  • Enertia Master
  • ***
  • Posts: 78
    • View Profile
    • Email
Re: Brammo Software
« Reply #16 on: April 05, 2019, 04:20:36 AM »
Very nice, my com ports are detected with this one, know let's order an ft232rl rs485 device !

Edit : could you tell me the power rating of the 12V power supply? How much Amps it outputs? Big thanks!
« Last Edit: April 05, 2019, 04:23:52 AM by nunux59 »

MiBa

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: Brammo Software
« Reply #17 on: April 05, 2019, 03:10:49 PM »
Thank you.

I've used a power supply: @12,5V current draw was only 60mA.

As I've a complete set of 7 almost unused original Battery-Modules as "spare parts",
I can test them individually out off the bike in my workshop.

Interesting note:
When the temperature is below 15°C the single module itself starts to self-heating itself once the Batt diag Tool is connected.

The Tool states -3,3A current "draw" @ 15,9V Module-Voltage.

Resulting in about 50W/Module, 350W/Pack.


So the module qualification test will fail in the "current draw"  sub-test (should be between -200 / +200mA).

At 15°C and higher the test will pass.


One Remark regarding the Heating:
I've observed up to 900W Energy consumption (measured at the outlet) once the Pack will be charged at low temps and the Dash shows a full pack with no balancing at cell- or pack-level anymore.

Regards
Michael

nunux59

  • Enertia Master
  • ***
  • Posts: 78
    • View Profile
    • Email
Re: Brammo Software
« Reply #18 on: May 16, 2019, 04:41:28 AM »
Nice, I am waiting for my RS485 module to arrive, to test this !

Epicurus

  • Newbie
  • *
  • Posts: 13
    • View Profile
Re: Brammo Software
« Reply #19 on: July 19, 2020, 03:29:24 PM »
Did you ever get the Empulse Battery cable working?

I'm trying to find out where to buy one for my Enertia.

Diogoborg

  • Newbie
  • *
  • Posts: 2
    • View Profile
    • Email
Re: Brammo Software
« Reply #20 on: August 25, 2020, 01:10:59 PM »
Hello!
I have a 2014 Empulse R  with a problem, but I live in the Azores Islands, in the middle of North Atlantic, therefore I have no tecnical support here.
Can you help me ?

It stopped working and the display shows "system failure s217".

This s217 error is not listed in the manual.

Does anybody have an idea how to solve this?
Thanks!

nunux59

  • Enertia Master
  • ***
  • Posts: 78
    • View Profile
    • Email
Re: Brammo Software
« Reply #21 on: September 29, 2020, 01:47:01 AM »
Hello!
I have a 2014 Empulse R  with a problem, but I live in the Azores Islands, in the middle of North Atlantic, therefore I have no tecnical support here.
Can you help me ?

It stopped working and the display shows "system failure s217".

This s217 error is not listed in the manual.

Does anybody have an idea how to solve this?
Thanks!

You should start a new thread about this. I don't know what this code is but you should start to diagnosis things one by one.